China Good quality Excavator Radial Piston Motor Hydraulic Gear Motor Wheel Motor Drive Motor with Hot selling

Product Description

Product Description

Excavator Radial Piston Motor Hydraulic Gear Motor Wheel Motor Drive Motor

1. Completely, assembly, and ready to installed in your excavators.

2. With MOTOR,

3. All components are produced by us.

4. All new, undamaged.

5. Painted or Unpainted, depend on requirement

6. 90 days warranty, call or email with any questions.

7. Plywood Case Packing, free of fumigation

8. Deliver to CHINAMFG by Sea, Air, or Carrier.

Engine Parts : Piston,liner, gasket set, bearing, valve, crankshaft,connect rod, camshaft,cyl block,cyl head, turbo,starter, water pump, alternator, feed pump, injector, fuel pump…….

Hydraulic Parts: Hyd pump,gear pump,regulator swing motor,travel motor,main control valve, panetary carrier assy,sun gear, panetary gear, cyl block&valve plater, piston shoe,……..

Undercarriage Parts: carrier roller,bottom/track roller, idler,sproker, track shoe, track link, adjust cyl,arm/boom/bucket cyl, adjust spring, exvavator bucket, bucket teeth/tip……

Electronic Parts : Throttle/stepper motor,electric appliance,Pressure Switch, Sensor, Switch Start Flameout Solenoid , monitor, controller/ECU……  

Cabin Parts : Complete Cabin, Cabin door, door panel, engine cover, Raditator, hyd oil cooler, Condenser, air condenser…….

Detailed Photos

 

Engine Parts Including:

Crankshaft Cylinder Head Cylinder Liner Cylinder Block
Camshaft Injector Filter Fuel Pump
Water Pump Piston Turbocharger Connecting Rod
Gear Ring Engine Assembly Flywheel Injection Valves
Bearing Bushes Full Gasket Set Intake Valve Exhaust Valve

Product Parameters

Applicable Models:

THE MODELS FOR EXCAVATOR/BULLDOZER 
FOR-HITACHI 
EX40-1 EX40-2 EX55 EX60 EX60-2 EX60-3 EX60-5 EX70 EX75
EX100 EX110 EX120 EX120-1 EX120-2 EX120-3 EX120-5 EX130-1 EX200-1
EX200-2 EX200-3 EX200-5 EX220-3 EX220-5 EX270 EX300 EX300-1 EX300-2
EX300-3 EX300-5 EX300A EX330 EX370 EX400-1 EX400-2 EX400-3 EX400-5
EX450 ZAX30 ZAX55 ZAX200 ZAX200-2 ZAX330 ZAX450-1 ZAX450-3 ZAX450-5
ZX110 ZX120 ZX200 ZX200-1 ZX200-3 ZX200-5G ZX200LC-3 ZX210 ZX210-3
ZX210-5 ZX225 ZX240 ZX250 ZX270 ZX300 ZX330 ZX330C ZX350
ZX450 ZX450LC ZX500 ZX500LC ZX520 ZX670 ZX690 ZX870 ZX130
ZX170 ZX170LC ZX195 ZX260 ZX360 ZX360LC ZX400 ZX470 ZX490
FOR-KOMATSU(EXCAVATOR)
PC20-7 PC30 PC30-3 PC30-5 PC30-6 PC40-7 PC45 PC45-2 PC55
PC120-6 PC130 PC130-7 PC200 PC200-1 PC200-3 PC200-5 PC200-6 PC200-7
PC200-8 PC210-6 PC220-1 PC220-3 PC220-6 PC220-7 PC220-8 PC270-7 PC202B
PC220LC-6 PC220LC-8 PC240 PC300 PC300-3 PC300-5 PC300-6 PC300-7 PC300-7K
PC300LC-7 PC350-6/7 PC400 PC400-3 PC400-5 PC400-6 PC400LC-7 PC450-6 PC450-7
PC600 PC650 PC750 PC800 PC1100 PC1250 PC2000    
FOR-KOMATSU(BULLDOZER)
D20  D31 D50 D60 D61 D61PX D65A D65P D64P-12
D80 D85 D155 D275 D355 D85PX D85EX D65EX  
FOR-CATERPILLAR(EXCAVATOR)
E200B E200-5 E320D E215 E320DL E324D E324DL E329DL E300L
E320S E320 E320DL E240 E120-1 E311 E312B E320BL E345
E324 E140 E300B E330C E120 E70 E322C E322B E325
E325L E330 E450 CAT225 CAT312B CAT315 CAT320 CAT320C CAT320BL
CAT330 CAT322 CAT245 CAT325 CAT320L CAT973  CAT939C CAT963C CAT313
CAT323 CAT318 CAT326 CAT328 CAT329 CAT336 CAT340 CAT345 CAT349
FOR*CAT-ERPILLAR(BULLDOZER)
D3 D3B D3C D3D D4 D4C D4D D4E D4H
D5 D5B D5C D5D D5H D5M D6 D6C D6D
D6H D6M D6R D6G D6N D7 D7C D7D D7E
D7F D7G D7H D7R D8 D8R D8N D8H D8T
D8L D8K D8G D8M D9 D9L D9N D9R D9T
D10 D10R D10N D10T D11 D11R D11N    
FOR-KOBELCO
SK120-6 SK120-5 SK210-8 SK210LC-8 SK220 SK220-1 SK220-3 SK220-5/6 SK200 
SK200 SK200  SK200-3 SK200-6 SK200-8 SK200-5/6 SK60 SK290 SK100
SK230 SK250 SK250-8 SK260LC-8 SK300 SK300-2 SK300-4 SK310 SK320
SK330-8 SK330 SK350LC-8 SK235SR SK450 SK480 SK30-6    
FOR-SUMITOMO
SH120  SH120-3 SH200 SH210-5 SH200 SH220-3 SH220-5/7 SH290-3 SH350-5/7
SH220 SH280 SH290-7 SH260 SH300 SH300-3 SH300-5 SH350 SH60
FOR-VOLVO
EC160C EC160D EC180B EC180C EC180D EC210 EC210 EC210B EC240B
EC290 EC290B EC240 EC55 EC360 EC360B EC380D EC460 EC460B
EC460C EC700 EC140 EC140B EC160B EC350 EC350DL EC480 EC340
FOR-LIEBHERR
R914 R924 R934 R944 R916 R926 R936 R954 R966
R974 R984              
FOR-KUBOTA
JH60-7 JH115 JH135 JH161 JH185        
FOR-DAEWOO
DH200 DH220-3 DH220 DH220S DH280-2 DH280-3 DH55 DH258 DH130
DH370 DH80 DH500 DH450 DH225 DH150 DH330 DH400 DH580
FOR-HYUNDAI
R60-5 R60-7 R80-7 R200 R200-3 R210 R210-1 R210-9 R210LC
R210LC-7 R225 R225-3 R225-7 R250 R250-7 R290 R290LC R290LC-7
R320 R360 R954 R205 R210-5 R215 R230 R235 R275
R300 R385 R485            
FOR-KATO
HD512 HD1430 HD512III HD820III HD820R HD1430III HD700VI HD1250VII HD250SE
HD400SE HD500SE HD1880            
FOR-DOOSAN
DX225 DX225LC DX258 DX300 DX300LCA DX420 DX430 DX140 DX150
DX220 DX250 DX255 DX260 DX370 DX480 DX520    
FOR-SHXIHU (WEST LAKE) DIS.I
SD13-2 DH16J2XL DH16J2LGP SD16 SD22 SD32      
FOR-CASE
CX210 CX210B CX210C CX210D CX210LC CX225 CX235 CX235C CX240
CX240C CX245 CX250 CX250C CX300 CX300C CX330 CX330C CX350
CX350C CX460 CX460LC CX470 CX470C CX490 CX490D CX700 CX700B
CX750 CX750D              
FOR-JCB
JS200 JS200SC JS210 JS210SC JS220 JS220LC JS230 JS230LC JS240
JS240LC JS290 JS290LC JS300 JS300LC JS330 JS330LC    
FOR-XCMG
XE55DA XE60DA XE65DA XE75DA XE80C XE80D XE85C XE85D XE135D
XE155DK XE150D XE155D XE200DA XE200D XE200C XE205DA XE215DA XE215C
XE215D XE215HB XE225DK XE230C XE245DK XE240D XE260C XE265C XE270DK
XE305D XE335DK XE335C XE370D XE370DK XE370CA XE370C XE380DK XE470D
XE490DK XE490CK XE500HB XE520DK XE550DK XE750D XE750G XE950D XE950G
XE950DA XE55 XE60 XE65 XE75 XE80 XE85 XE135 XE150
XE155 XE200 XE205 XE215 XE225 XD230 XE240 XE245 XE260
XE265 XE270 XE305 XE335 XE370 XE380 XE470 XE490 XE500
XE520 XE550 XE750 XE950          
FOR-MITSUBISHI
MS30 MS110 MS110-3 MS110-5 MS110-8 MS180      
FOR-SAMSUNG
SE210 SE280 SE320            
FOR-IHI
IHI35 IHI50 IHI55 IHI60 IHI75        
FOR-YMMA
YM15 YM30 YM35 YM55 YM65 YM85      
FOR-LIUGONG
LG906C LG907 LG200 LG220 LG925 LG934      

 

Packaging & Shipping

Company Profile

19 Years Exported Experience, Various Parts in Stock
Specialized deal for Construction Machinery Diesel Engine Parts
Related Undercarriage Spare Parts:

 

 

Our Advantages

FAQ

Q1: Are you trading company or manufacturer ?

A: We are an industry and trade integrated enterprise.

Q2. What are your terms of payment?

A: T/T 30% as deposit, and 70% before delivery. We’ll show you the photos of the products and packages before you pay the balance.

Q3. What are your terms of delivery?

A: EXW, FOB, CFR, CIF.

Q4: Do you provide samples ? Is it free or extra ?

A: It depends on the product value and can be negotiated.

Q5. How about your delivery time?

Generally, the specific delivery time depends on the items and the quantity of your order.

Q6. Do you test all your goods before delivery?

A: Yes, we have 100% test before delivery

Q7: How do you make our business long-term and good relationship?

A:1. We keep good quality and competitive price to ensure our customers benefit ;

2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.

/* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service: Technical Support
Warranty: 12 Months
Type: Crawler Excavator
Usage: Special Excavator, Marine Excavator, Mining Excavator, GM Excavator
Bucket: Backhoe
Transmission: Hydraulic Transmission
Samples:
US$ 1/Piece
1 Piece(Min.Order)

|

Customization:
Available

|

gear motor

What are the maintenance requirements for gear motors, and how can longevity be maximized?

Gear motors, like any mechanical system, require regular maintenance to ensure optimal performance and longevity. Proper maintenance practices help prevent failures, minimize downtime, and extend the lifespan of gear motors. Here are some maintenance requirements for gear motors and ways to maximize their longevity:

1. Lubrication:

Regular lubrication is essential for gear motors to reduce friction, wear, and heat generation. The gears, bearings, and other moving parts should be properly lubricated according to the manufacturer’s recommendations. Lubricants should be selected based on the motor’s specifications and operating conditions. Regular inspection and replenishment of lubricants, as well as periodic oil or grease changes, should be performed to maintain optimal lubrication levels and ensure long-lasting performance.

2. Inspection and Cleaning:

Regular inspection and cleaning of gear motors are crucial for identifying any signs of wear, damage, or contamination. Inspecting the gears, bearings, shafts, and connections can help detect any abnormalities or misalignments. Cleaning the motor’s exterior and ventilation channels to remove dust, debris, or moisture buildup is also important in preventing malfunctions and maintaining proper cooling. Any loose or damaged components should be repaired or replaced promptly.

3. Temperature and Environmental Considerations:

Monitoring and controlling the temperature and environmental conditions surrounding gear motors can significantly impact their longevity. Excessive heat can degrade lubricants, damage insulation, and lead to premature component failure. Ensuring proper ventilation, heat dissipation, and avoiding overloading the motor can help manage temperature effectively. Similarly, protecting gear motors from moisture, dust, chemicals, and other environmental contaminants is vital to prevent corrosion and damage.

4. Load Monitoring and Optimization:

Monitoring and optimizing the load placed on gear motors can contribute to their longevity. Operating gear motors within their specified load and speed ranges helps prevent excessive stress, overheating, and premature wear. Avoiding sudden and frequent acceleration or deceleration, as well as preventing overloading or continuous operation near the motor’s maximum capacity, can extend its lifespan.

5. Alignment and Vibration Analysis:

Proper alignment of gear motor components, such as gears, couplings, and shafts, is crucial for smooth and efficient operation. Misalignment can lead to increased friction, noise, and premature wear. Regularly checking and adjusting alignment, as well as performing vibration analysis, can help identify any misalignment or excessive vibration that may indicate underlying issues. Addressing alignment and vibration problems promptly can prevent further damage and maximize the motor’s longevity.

6. Preventive Maintenance and Regular Inspections:

Implementing a preventive maintenance program is essential for gear motors. This includes establishing a schedule for routine inspections, lubrication, and cleaning, as well as conducting periodic performance tests and measurements. Following the manufacturer’s guidelines and recommendations for maintenance tasks, such as belt tension checks, bearing replacements, or gear inspections, can help identify and address potential issues before they escalate into major failures.

By adhering to these maintenance requirements and best practices, the longevity of gear motors can be maximized. Regular maintenance, proper lubrication, load optimization, temperature control, and timely repairs or replacements of worn components contribute to the reliable operation and extended lifespan of gear motors.

gear motor

How does the voltage and power rating of a gear motor impact its suitability for different tasks?

The voltage and power rating of a gear motor are important factors that influence its suitability for different tasks. These specifications determine the motor’s electrical characteristics and its ability to perform specific tasks effectively. Here’s a detailed explanation of how voltage and power rating impact the suitability of a gear motor for different tasks:

1. Voltage Rating:

The voltage rating of a gear motor refers to the electrical voltage it requires to operate optimally. Here’s how the voltage rating affects suitability:

  • Compatibility with Power Supply: The gear motor’s voltage rating must match the available power supply. Using a motor with a voltage rating that is too high or too low for the power supply can lead to improper operation or damage to the motor.
  • Electrical Safety: Adhering to the specified voltage rating ensures electrical safety. Using a motor with a higher voltage rating than recommended can pose safety hazards, while using a motor with a lower voltage rating may result in inadequate performance.
  • Application Flexibility: Different tasks or applications may have specific voltage requirements. For example, low-voltage gear motors are commonly used in battery-powered devices or applications with low-power requirements, while high-voltage gear motors are suitable for industrial applications or tasks that require higher power output.

2. Power Rating:

The power rating of a gear motor indicates its ability to deliver mechanical power. It is typically specified in units of watts (W) or horsepower (HP). The power rating impacts the suitability of a gear motor in the following ways:

  • Load Capacity: The power rating determines the maximum load that a gear motor can handle. Motors with higher power ratings are capable of driving heavier loads or handling tasks that require more torque.
  • Speed and Torque: The power rating affects the motor’s speed and torque characteristics. Motors with higher power ratings generally offer higher speeds and greater torque output, making them suitable for applications that require faster operation or the ability to overcome higher resistance or loads.
  • Efficiency and Energy Consumption: The power rating is related to the motor’s efficiency and energy consumption. Higher power-rated motors may be more efficient, resulting in lower energy losses and reduced operating costs over time.
  • Thermal Considerations: Motors with higher power ratings may generate more heat during operation. It is crucial to consider the motor’s power rating in relation to its thermal management capabilities to prevent overheating and ensure long-term reliability.

Considerations for Task Suitability:

When selecting a gear motor for a specific task, it is important to consider the following factors in relation to the voltage and power rating:

  • Required Torque and Load: Assess the torque and load requirements of the task to ensure that the gear motor’s power rating is sufficient to handle the expected load without being overloaded.
  • Speed and Precision: Consider the desired speed and precision of the task. Motors with higher power ratings generally offer better speed control and accuracy.
  • Power Supply Availability: Evaluate the availability and compatibility of the power supply with the gear motor’s voltage rating. Ensure that the power supply can provide the required voltage for the motor’s optimal operation.
  • Environmental Factors: Consider any specific environmental factors, such as temperature or humidity, that may impact the gear motor’s performance. Ensure that the motor’s voltage and power ratings are suitable for the intended operating conditions.

In summary, the voltage and power rating of a gear motor have significant implications for its suitability in different tasks. The voltage rating determines compatibility with the power supply and ensures electrical safety, while the power rating influences load capacity, speed, torque, efficiency, and thermal considerations. When choosing a gear motor, it is crucial to carefully evaluate the task requirements and consider the voltage and power rating in relation to factors such as torque, speed, power supply availability, and environmental conditions.

gear motor

What is a gear motor, and how does it combine the functions of gears and a motor?

A gear motor is a type of motor that incorporates gears into its design to combine the functions of gears and a motor. It consists of a motor, which provides the mechanical power, and a set of gears, which transmit and modify this power to achieve specific output characteristics. Here’s a detailed explanation of what a gear motor is and how it combines the functions of gears and a motor:

A gear motor typically consists of two main components: the motor and the gear system. The motor is responsible for converting electrical energy into mechanical energy, generating rotational motion. The gear system, on the other hand, consists of multiple gears with different sizes and tooth configurations. These gears are meshed together in a specific arrangement to transmit and modify the output torque and speed of the motor.

The gears in a gear motor serve several functions:

1. Torque Amplification:

One of the primary functions of the gear system in a gear motor is to amplify the torque output of the motor. By using gears with different sizes, the input torque can be effectively multiplied or reduced. This allows the gear motor to provide higher torque at lower speeds or lower torque at higher speeds, depending on the gear arrangement. This torque amplification is beneficial in applications where high torque is required, such as in heavy machinery or vehicles.

2. Speed Reduction or Increase:

The gear system in a gear motor can also be used to reduce or increase the rotational speed of the motor output. By utilizing gears with different numbers of teeth, the gear ratio can be adjusted to achieve the desired speed output. For example, a gear motor with a higher gear ratio will output lower speed but higher torque, whereas a gear motor with a lower gear ratio will output higher speed but lower torque. This speed control capability allows for precise matching of motor output to the requirements of specific applications.

3. Directional Control:

Gears in a gear motor can be used to control the direction of rotation of the motor output shaft. By employing different combinations of gears, such as spur gears, bevel gears, or worm gears, the rotational direction can be changed. This directional control is crucial in applications where bidirectional movement is required, such as in conveyor systems or robotic arms.

4. Load Distribution:

The gear system in a gear motor helps distribute the load evenly across multiple gears, which reduces the stress on individual gears and increases the overall durability and lifespan of the motor. By sharing the load among multiple gears, the gear motor can handle higher torque applications without putting excessive strain on any particular gear. This load distribution capability is especially important in heavy-duty applications that require continuous operation under demanding conditions.

By combining the functions of gears and a motor, gear motors offer several advantages. They provide torque amplification, speed control, directional control, and load distribution capabilities, making them suitable for various applications that require precise and controlled mechanical power. Gear motors are commonly used in industries such as robotics, automotive, manufacturing, and automation, where reliable and efficient power transmission is essential.

China Good quality Excavator Radial Piston Motor Hydraulic Gear Motor Wheel Motor Drive Motor   with Hot selling	China Good quality Excavator Radial Piston Motor Hydraulic Gear Motor Wheel Motor Drive Motor   with Hot selling
editor by CX 2024-01-19

Gear Motor

As one of the gear motor manufacturers, suppliers, and exporters of mechanical products, We offer gear motors and many other products.

Please get in touch with us for details.

Manufacturer supplier exporter of gear motors.

Recent Posts